DOD Contract : SPE40002D9411 | SPE400-02-D-9411

Federal Supply Classes for SPE40002D9411

1560 - Airframe Structural Components

Includes: Includes Flight Control Surfaces; Internal and External Auxiliary Fuel Tanks; Exhaust Systems; Pylons, Trim Tabs; Aircraft.

Excludes: Excludes Fitted Covers; Helicopter Rotor Brake System Components; Aircraft Loose Equipment and Alternate Mission Configuration Equipment stored on board the aircraft.

Note: Note-This class includes fabricated system parts that are permanently attached or peculiar to the integral airframe of an aircraft, such as support structural components, spars, ribs, ailerons, stabilizers, bulkheads.

1650 - Aircraft Hydraulic, Vacuum, and De-icing System Components

Includes: Includes Hydraulic and Pneumatic Accumulators, Pumps, Motors, Actuating Cylinders, and Filters; De-icing Boots; Fluid Type De-icing Pumps, Valves and Filters; Vacuum System Oil Separators; Pneumatic Pressurization Equipment other than that for pressurizing cabins and compartments.

Excludes: Excludes Jet Engine Hydraulic Components (FSC 2840); Valves specifically designed for air conditioning, heating, ventilating, cabin pressurizing, and thermal de-icing (FSC 1660); Valves specifically designed for use with Aircraft Engines (FSC 2840); Guided Missiles and Guided Missile Engines (FSC 1338), Landing Gear (FSC 1620), Wheel and Brake System Components (FSC 1630); Oxygen Breathing System Components (FSC 1660); In-flight Refueling System Hydraulic components (FSC 1680); Specifically designed hydraulic power steering system components (FSC 1620).

Note: Note-This class includes only those components specifically designed for aircraft use.

1660 - Aircraft Air Conditioning, Heating, and Pressurizing Equipment

Includes: Includes Cabin Supercharging Equipment; Canisters; Cylinder Assemblies; Masks; Fixed Oxygen System; Specially Designed Aircraft Valves; Cabin Pressure Regulators; Heat Exchangers; Air Expansion Turbines; Aircraft Heaters; Ventilating System Components; Air Conditioning and Heating Duct Assemblies; Thermal De-icing Equipment; Cabin and Compartment Pressurizing Equipment; Air Diffusers; Cabin Pressure Selectors; Liquid Oxygen Converters.

Excludes: Excludes Oxygen Pressure Signals and Warning Devices; Tubing; Ground Type Heaters and Coolers; Pressurizing Equipment other than that used for Cabin and Compartment Pressurization; Fluid De-icing Equipment; Valves specifically designed for use with Aircraft Engines, Guided Missiles, and Guided Missile Engines.

Note: Note-This class includes components specifically designed for use in aircraft air conditioning, heating, and pressurizing equipment. Also included are specially designed components of oxygen breathing systems used in aircraft.

1670 - Parachutes; Aerial Pick Up, Delivery, Recovery Systems; and Cargo Tie Down Equipment

Includes:

Excludes: Excludes Fitting Assemblies built into the aircraft structure.

Note: Note-Includes specifically designed items, sets, and systems for air-to-air, air-to-surface, and surface-to-air delivery, pick up, and recovery operations, unless parts, attachments, assemblies, for use in or on such systems (i.e., space vehicle aerial recovery systems) are specifically indexed to other classes of the FSC (i.e., Transmitting Radio Buoys and Direction Finding Subsystem Components).

1680 - Miscellaneous Aircraft Accessories and Components

Includes: Includes Control Assemblies, Push-Pull; Brace, Positioning Cargo Ramp stowed on board; Cockpit Mounted Control Quadrants; Actuators, Electro-Mechanical and Mechanical; Ventilators; Relief Tubes; Map Holders; Aerial Glider Towing Accessories attached to Aircraft; Belts, Safety and Lap; Harness, Shoulder and Safety; Litter Attaching Supports;Electric Windshield Wipers;Aircraft Onboard Inert Gas Generators;Aircraft Furniture;Aircraft Mounted Winches and Hoists;In-Flight Refueling System Components, including Fuel Components;Aircraft Curtains;Cable Tension Regulators;Sun Visors;Rear-View Mirrors;Mechanical Transmissions, Gearboxes and Constant Speed drives Specially designed for aircraft.

Excludes: Excludes Engine Mounted Control Assemblies; Fitted Covers, Aircraft Pylons; Helicopter Roter Brake System Components; Helicopter Automatic Stabilization Equipment.

3120 - Bearings, Plain, Unmounted

Includes: Includes Sleeve Bearings; Split Bearings; Washer Type Bearings; Jewel Bearings.

Excludes: Excludes Antifriction Bearings (FSC 3110); Mounted Bearings (FSC 3130).

Note: Note-Bearings in this class are generally one piece that retain and position moving and/or rotating parts. They may have lubrication grooves/fittings/facilities or include pre-lubrication.

4710 - Pipe, Tube and Rigid Tubing

Includes: Includes Culvert Pipes; Culvert Pipe Connector Bands; Metallic Pipes; Plastic Pipes; Tubes and Rigid Tubing and their assemblies.

Excludes: Excludes Air Conditioning-Heating Pipes (FSC 4520); Asbestos and Cement, Bituminized Fiber, Clay and Concrete Pipes (FSC 5630); Conduit Pipes and their assemblies (FSC 5975); Downspout Pipes (FSC 5670); Exhaust Pipes (FSC 1560, 2990, and 4520); Fire Extinguishing Systems Pipes and Tubes and their assemblies (FSC 4210); Flexible Tubing (FSC 4720); Glass Tubing (FSC 6640, and 9340); Laboratory Tubes (FSC 6640); Medical and Surgical Tubes (FSC 6515).

4920 - Aircraft Maintenance and Repair Shop Specialized Equipment

Includes: Includes Maintenance stands designed for support of aircraft assemblies during repair or overhaul; Test Stands and Test Equipment specially designed for maintenance and repair of aircraft components such as: engines, generators, hydraulic systems, armament, automatic pilot, fire control, flight control, and navigational systems.

Excludes: Excludes Hand Tools; Airfield Maintenance Platforms; Basic types of electrical and electronic test instruments, including those specially designed, such as ammeters, voltmeters ohmmeters, multimeters, and similar instruments, as shown in the indexes to the FSC; Test Apparatus used for both communications and other electrical and electronic equipment.

5310 - Nuts and Washers

Includes: Includes Locknuts; Eye Nuts; Plain Nuts; Castellated Nuts; Wing Nuts; Plate Nuts; Push on Nuts; Concave and Convex Washers; Flat Washers; Keyed Washers; Lock Washers; Shouldered Washers; Split Washers.

Excludes: Excludes Bearing Thrust Washers (FSC 3120); Shims (FSC 5365); Ring Spacers (FSC 5365); Plate Spacers (FSC 5365); Lock Rings (FSC 5365).

Note: Note-Nuts and washers, including specially designed, are to be classified in this FSC. a. Nuts are a small metal block made in a variety of shapes such as square and hexagonal which is drilled and internally threaded. b. Washers are a perforated piece of metal, leather, or other materials of various shapes or forms. They are used primarily as a seat for a bolt, nut, screw, rivet or nail to distribute pressure and prevent endwise motion over an area and/or to prevent movement between two parts by means of restraining features created by the shape of its edges.

5315 - Nails, Machine Keys, and Pins

Includes: Includes Dowel Pins, Split Pins; Spikes; Tacks; Nonoffice Type Staples; Machine Keys; Brads; Shouldered Pins; Cotter Pins; Nails.

Excludes: Excludes Shafts (FSC 3040); Lock Keys (FSC 5340).

Note: Note-Nails, machine keys, and pins, including specially designed, will be classified in this FSC. a. Nails are slender, usually pointed fasteners with a head, and designed for insertion by impact. b. Machine keys are items generally inserted between two items, usually in a groove, to prevent relative rotation e.g., shaft and hub. c. Pins are cylindrical items of various materials used to align/attach two or more parts together and may allow for angular movement.

5330 - Packing and Gasket Materials

Includes: Includes General Purpose Oil Grease, Air, Liquid, Gas, and chemical Seals; Oakum; Prefabricated Gaskets and Seals designed for a single specific application.

Excludes: Excludes O-Rings (FSC 5331); Bulk material items, such as; Rubber, Cork, and Asbestos Sheets and Strips (FSG 93); Liquid Gasket Materials (RTV, Permatex, etc.) (FSG 80); RFI and EMI Seals and Gaskets (FSC 5999), and all Seal Retainers.

Note: Note-This FSC includes only seals and gaskets designed for standard use. Seals, gaskets and packing are made from materials specifically designed and constructed to resist deterioration from the action of heat, gas, chemicals, liquids, and used to fill a cavity and create a tight seal. Similar materials used to make seals, gaskets, and packing are available in bulk form, refer to FSG 93, FSG 80, and FSG 83.

5340 - Hardware, Commercial

Includes: Includes Access Covers; Bumpers; Casters; Cabinet and Door Hardware; Clevises; Hinges; Latches; Straps and Strapping; Turnbuckles; Webbed Straps.

Excludes: Excludes Weapons System Hardware (FSC 5342).

Note: Note-Common hardware designed primarily for commercial use will be classified in this FSC. Hardware is the physical, tangible and permanent components of end items that may not be classified elsewhere. It consists also of common items that are commonly used in construction and/or manufacturing (e.g., hinges, door locks).

5365 - Bushings, Rings, Shims, and Spacers

Includes: Includes Externally Threaded Rings; Keyed and Serrated Lock Rings; Dee Rings; Instrument Retaining Rings; Shim Sets and Assortments; Plate Spacers; Ring Spacers; Sleeve Spacers; Stepped Spacers; Spacer Sets and Assortments; Sleeve Bushings; Machine Threaded Bushings; Machine Threaded Plugs.

Excludes: Excludes Sleeve Bearings (FSC 3120); Pipe Threaded Plugs (FSC 4730); Piston Rings (FSC 2520, 2805, 2810, 2815, 2825, 2990, 3040, 4310, and 4820); Retaining Rings (FSC 5325); Shim Stock (FSC 9515).

Note: Note-All items, including specially designed, will be classified in this FSC. a. A bushing is cylindrical in shape, hollow, and designed primarily to be inserted into a hole to reduce the effective inside diameter of the hole, and to protect the body structure about the hole from damage resulting from stress, strain, and vibration. b. A ring is cylindrical in shape, usually flat with a center hole. Rings are multi-applicational. See specific item name for designated usage. c. A shim is a thin, sometimes tapered, piece of material used to fill in space between things. See specific item name for dimensional parameters. d. A spacer is a device for holding two members at a given distance from each other.